You never know. Old filament CAN be used, but it takes special care with the slicer settings and it helps a lot if you have a dehumidifier to dry it out. I live in a dry climate, and have filament at work which has been sitting on the shelf for about 7 years, but I can still get beautiful prints out of it. All of my filament at home is left in ziplock bags but it still gets brittle over time (if you can easily snap the filament, it probably has a lot of moisture in it).

I wonder if this is a matter of countries refusing to choose a side (by not recognizing new countries), or if they ARE choosing to side with the aggressive countries?

Seems like a lot of shitty countries are trying to make land-grabs all at once, with the goal being to wipe out the existing population. I figure it’s only a matter of time before China starts trying to commit genocide on Taiwan, but Russia and Israel have already jumped into that pool.

Honestly at that point I would tear down the whole thing and use this video as a guide for reassembly. The most important thing to do is to make sure the framework is all squared up, otherwise all prints will suffer.

As for bed leveling… A lot of people think the paper test is all you need, but really that only gets you close enough to start leveling the bed. First thing is to tighten all the springs to within 1 turn of being closed, then adjust the Z switch so that the head homes to roughly that same height. After that you use the paper method to get the bed roughly level, then move on to live testing with a 5-point bed-leveling test print to dial it in. Ideally you want the nozzle gap to be about 75% of the nozzle size, so for a 0.20mm tip you would want a 0.15mm gap to get your print to stick.

As I mentioned to someone else, Creality’s QC is garbage. My first glass bed had better adhesion than PEI and worked beautifully for a few years until the coating wore out. My second glass bed was trash, I never could get anything to stick to it without using hairspray, and now it sits in its box. I have a PEI bed now, which seems to have solved the problem. If you decide to try using the printer again, don’t forget to clean the glass with 90% ISO. Worst case try flipping the glass over to the smooth side, clean it with ISO, then use glue sticks on that surface (you won’t get any adhesion on bare glass without the glue or hairspray).

Ah thanks for that! I can never remember PETG, probably because I’ve never used it myself.

OK so you want to watch this video and learn how to manually do bed leveling. However if you really want to go over the whole machine (perhaps even tearing it down and rebuilding it so you know where everything is an can assure that it was assembled correctly) the you want to start with this video.

Once the machine is set up, it’s time to install slicing software on your computer. Cura is a popular and free option, with support built in for the Ender 3 (you have to set up a new machine in the software and tell it what model you have). Following that, find something to print! There are many sites like thingiverse where you can download models from, but you want to start with something small to work out the bugs without wasting a lot of filament. Look for something like a calibration cube (“calicat” is my favorite) which will provide information on how well you have your machine set up.

Also to consider… if you live in a humid environment and you were given filament with the printer that is NOT in a sealed bag, you should be aware that filament absorbs moisture from the air and “wet” filament will print like hot garbage. Insanely cheap filament like the $12 stuff you find on Amazon can also cause problems, so stick with stuff more in the $20 range until you have some experience in working with your machine.

One thing I learned is that Creality’s QC is absolute garbage. When I first got my printer I also picked up a glass plate. Everything stuck perfectly to it, hardly any fuss at all. After several years the coating wore out and I bought a new one. Total trash, nothing would stick without heavy usage of hair spray and I eventually gave up on it.

If you want to try again, look for PEI beds. If you have one with the magnetic base, there are several with the PEI already mounted on a spring-steel plate. PEI is one of the best surfaces you will ever find to print on, although I believe one type of filament (I think a variation of PLA?) sticks too well and can damage the PEI trying to take prints off… but I’ve used regular PLA, PLA+, and TPU with great success, and have heard that ABS also works well on it. Just keep it clean with 90% ISO and you’ll eliminate at least one problem.

Of course there’s also the whole thing with bed leveling. I run into a lot of people who think the paper method is the whole process for leveling, when really it’s just to get your printer dialed in close enough that you don’t ruin the bed when you actually begin to do the leveling. Getting the leveling wrong is by far the most common reason why prints don’t stick well so do your best to nail that aspect. You want the nozzle gap about 3/4 of the nozzle size, so for a standard 0.20mm nozzle you would want a gap of about 0.15mm for your first layer (but still use 0.20 in the slicer) to get that proper smoosh. My leveling method involves using a 5-point bed-leveling test print, and you can judge the gap by eye from that. Takes quite a few iterations to get all the corners dialed in, but you shouldn’t have to do it often.

Speaking of which… another common complaint is the loose bed springs. You want to Crank those puppies down almost completely closed, then adjust the Z switch to that new position before starting the leveling. Tight springs means you almost never have to readjust the leveling knobs. I check mine about once a year.

I bitched at someone on reddit about that once… Asked a similar common question and so I asked them if they even bothered LOOKING at the sub before they posted because that exact question had already been asked three times that day! There’s being lazy, and then there’s crap like this.

People give the Ender 3 a bad rap all the time, but it’s honestly a great little machine. I far prefer it to the $2500 printer we have at work that has “automatic everything” and can’t easily be adjusted to manually correct its bad settings.

With that said, how far have you gotten with it? Do you have any software installed? Have you tried printing anything (and was it successful)? You didn’t give much clue as to where you’re stuck. Yes you need to take some time to learn how to fine-tune the settings, and yes it can be frustrating because there is SO MUCH to learn about 3D printing, but once you get over the hump you can start cranking out all kinds of fun things.

Back in the days when people still had floppies and cd drives in their computers, yeah things were dead-simple. You pop in a disk, format the hard drive, and walk away while the process completes. I miss that. The machines I’ve worked on in probably the last decade, it seems like I have to fight against the hardware every time I want to wipe the system or replace a failed drive. The last set of servers I got, I couldn’t figure out why the linux image (with full EFI settings) refused to even boot up properly. Turns out Dell had made these machines so you could easily boot a Windows installer from any of the external USB ports, but to install linux you had to use a hidden internal USB port. Once I found out about that then yeah the installation went as planned, but this is the kind of BS I’m referring to about manufacturers trying to prevent users from getting rid of Windows.

Taiwan is not recognized by most countries.

Damn, they’re not? I thought I had heard otherwise. That’s a real shame, people should have the right to govern themselves they way they desire.

Just curious, but have you ever tried installing Windows from scratch on a new computer? I’m just wondering if your comparison of “simpler” is the same installation of both operating systems, or if you’re comparing something that somebody else set up for you to something you’re doing yourself?

And yeah, it DID used to be dead simple… throw in an installation media and boot up the machine. These days there’s so much garbage in the way that they’re complicated the whole process without much gain.

Don’t feel bad, that’s a shitty process even for those of us in IT. Sometimes it doesn’t work for certain models of memory sticks, sometimes something on the computer gets in the way of booting to the drive. I recently worked on some servers where I had to disable EFI, grab a 15 year old installer to get linux booted up on it, then switch to the newer installer to complete the process. So far Dell has been the worst (but also the most frequently used) I’ve had trouble with for getting linux installed. Unfortunately the solutions usually involve combinations of disabling EFI, changing the hard drive to a different mode, or even changing what mode the memory stick is booted with (all selected from within the BIOS at boot time), and it’s not always the same process even for the same release of a machine.

It’s not you, it’s Microsoft working with the manufacturers to make it difficult for people to switch.

Want to see shit really hit the fan? Imagine if Taiwan applied for NATO membership. They are already recognized by most countries as an independent entity and I assume are aligned with many Western goals since they conduct joint military exercises with the US, but China would go crazy over attempts at NATO membership.

Makes me wonder if there are are any rules to prevent acceptance if a country is attacked because of asking to join? Like I know Ukraine can’t join right now because they’re already at war (despite whatever Russia wants to call it), but I think Taiwan is not officially at war with anyone.

I’ll just add that nearly all linux distributions have a package manager you can access from the desktop. Simply open it up, find the software you want, and click to install. Not much different than going to the play store and installing an android app. The only time you need to do anything different is if you’re trying to install some obscure software that isn’t directly supported by your linux distribution, then you might have to resort to the command line.

To answer your first question, ALL of the mirrors are safe. The idea with mirrors is that you choose one that is geographically close to your location (same country, maybe the same region or state) to help reduce lag in downloading the files. Any selection is valid, all of the mirrors will have the same content, but for your location some mirrors may simply be faster or slower than others.

One other thing you might run in to is different types of installers. Some may be a very minimal install which only give you a command line, while others will provide a fully configured desktop. You might also see an option for a “Live” version – that is something you put on a bootable memory stick and you can test out a working version of the operating system without actually changing anything on your computer, but all of your settings will go away when you reboot.

I haven’t used Mint so I can’t provide specific info, however some things that are common to ANY linux desktop – You probably want to start with printer drivers (install CUPS) and some office software (install LibreOffice). For internet access, Firefox and Thunderbird are good choices. LicreOffice, Firefox, and Thunderbird can all also be used on Windows if you want to check them out ahead of time. There are many lists online that can point you to equivalent software, so like if you use Lightroom on windows, you might try Darkroom on linux. basically you just need to make a list of what Windows software you use and then install a similar package in linux.

Yes you will need some time to learn the new operating system and all the new software, very little will be 100% exactly the same, but they are “close enough”. You figured out how to use all these things once before, so you can do it again, and it will definitely be worth the effort.

Was it his right hand, or did he decide to go strange and choose the left hand? It’s not like he thinks anyone else is qualified to be in his presence.

So let me get this straight… Microsoft demanded all PC manufactures change their keyboards to add a new key that is only useful in Windows (at a considerable cost to manufacturers), and now that key doesn’t do anything? No wait, I shouldn’t be surprised.

Don’t you just hate spell-checkers changing your words?

I’m certainly not the type to get out on a bike and ride 50 miles a day, but on the other hand despite spending a lot of time at the computer I also spend a lot of time working on projects and moving around. Just this week I started cutting up the steel to build a new utility trailer so I certainly move around a lot, but my body still hates me.

I wish this helped me, but my back always starts hurting when I go for walks… although it’s more my middle-back rather than lower. I try to get in a 30-minute walk at least twice a week, plus of course things like going to the grocery store and mowing the lawn add a lot of time. Never seems to be enough to help though.